11:57 AM
Unknown
Surface Mount Technology (SMT) is a technology of soldering electrical components onto the pre-printed circuit boards. In order to make the whole process possible, SMT reflow soldering oven is usually used. This is a machine that employs high level of technology and bonding principles in its functionality. It is very complex but offers reliability and better alternative in the field of electrical assembly. This comes with advantages such as reduced board cost, controlled manufacturing and assembling process and reduced material handling.
The reflow soldering is the process of joining electronic devices to the printed circuit boards as the contact pads. This requires the use of solder paste and heat to attach the components. It is the SMT reflow soldering oven that is best in this. It allows for better control of heating process that minimizes chances of defective components.
It involves joining of electrical components on to contact pads with solder paste and heat. In the process of highly controlled heating that take place in the oven, solder melts in the right position and permanently join the electrical components on PCB in the process.
The PCB and loosely attached components is then drawn into the heating chambers through a conveyor belt. This then undergoes into four distinct phases in this machine. The first phase is known as preheat zone. This is where the melting point of the solvent is set. The ramp rate (time/temperature rate) is also determined and used to control heating in the following stages.
This is followed by thermal soak zone where the PCB and its components are exposed to heating at specific temperature for between 60 to 120 seconds to remove paste volatiles. The third stage is reflow zone. At this stage, PCB gets exposed to the maximum possible temperature that is tolerable by all the electronics on it. This is usually set below the liquidus temperature-the temperature above which the electronics get destroyed. At this point, the surface tension at the joints and the joints is reduced, melting the solder and as such bonding the pads and electronics.
The cooling zone is the last phase where controlled cooling is done to avoid thermal shock. This result of this is permanent bonding of the electrical components to PCB ready for use in electronic market after cleaning and testing.
The oven gets heated by ceramic heaters and heat transfer to the assembly points can be through radiation (hot air) or the infrared electromagnetic radiation depending on the machine make. Other technologies of heat transfer are also used.
These machines have gained favor with electronic assemblers for various reasons. These include simple methods of operating, faster production, high level of accuracy, produces much more component per unit time than any other method. In addition to this, depending on the model, it is possible to attach the components on both sides of PCB and there is efficiency in electricity utilization.
In order to remain relevant in electrical assembly industry, just like any other industry, it is important to use highly efficient and most up-to-date technology. There are latest models SMT reflow soldering oven that offers efficiency level that results to high productivity and profitability to a firm.
The reflow soldering is the process of joining electronic devices to the printed circuit boards as the contact pads. This requires the use of solder paste and heat to attach the components. It is the SMT reflow soldering oven that is best in this. It allows for better control of heating process that minimizes chances of defective components.
It involves joining of electrical components on to contact pads with solder paste and heat. In the process of highly controlled heating that take place in the oven, solder melts in the right position and permanently join the electrical components on PCB in the process.
The PCB and loosely attached components is then drawn into the heating chambers through a conveyor belt. This then undergoes into four distinct phases in this machine. The first phase is known as preheat zone. This is where the melting point of the solvent is set. The ramp rate (time/temperature rate) is also determined and used to control heating in the following stages.
This is followed by thermal soak zone where the PCB and its components are exposed to heating at specific temperature for between 60 to 120 seconds to remove paste volatiles. The third stage is reflow zone. At this stage, PCB gets exposed to the maximum possible temperature that is tolerable by all the electronics on it. This is usually set below the liquidus temperature-the temperature above which the electronics get destroyed. At this point, the surface tension at the joints and the joints is reduced, melting the solder and as such bonding the pads and electronics.
The cooling zone is the last phase where controlled cooling is done to avoid thermal shock. This result of this is permanent bonding of the electrical components to PCB ready for use in electronic market after cleaning and testing.
The oven gets heated by ceramic heaters and heat transfer to the assembly points can be through radiation (hot air) or the infrared electromagnetic radiation depending on the machine make. Other technologies of heat transfer are also used.
These machines have gained favor with electronic assemblers for various reasons. These include simple methods of operating, faster production, high level of accuracy, produces much more component per unit time than any other method. In addition to this, depending on the model, it is possible to attach the components on both sides of PCB and there is efficiency in electricity utilization.
In order to remain relevant in electrical assembly industry, just like any other industry, it is important to use highly efficient and most up-to-date technology. There are latest models SMT reflow soldering oven that offers efficiency level that results to high productivity and profitability to a firm.
About the Author:
You can visit the website www.sikama.com for more helpful information about SMT Reflow Soldering Oven: How It Work
0 comments:
Post a Comment